Canon PIXMA G3260
shows an error code or warning light.
Canon PIXMA G3260 shows an error code or warning light? A code or blinking light is useful only when it is tied to the exact model. Record the pattern first, then clear the low-risk causes before resetting anything. On this tank model, check Canon PRINT discovery, GI-21 ink flow, and rear-tray paper alignment first. Check the exact supply and indicator pattern for this model below.
Try these in order.
Stop as soon as the printer behaves. Each step removes one likely cause without changing settings you may need later.
- An alarm light keeps blinking
- The display shows a code or an ink level warning
- The printer refuses jobs while the warning remains
- Canon PIXMA G3260 behavior points back to Canon PRINT discovery, GI-21 ink flow, and rear-tray paper alignment.
- 01
Record the exact code or blink pattern
Write down every letter, number, color, and blink count before power-cycling. Different patterns can point to completely different fixes. On the Canon PIXMA G3260, use Canon PRINT or the 2-line monochrome LCD for this check.
Expected result: You have a precise record of the code or blink pattern.
- 02
Check covers, ink tanks, and the maintenance box
Open and close each access door, refill any empty ink tank, and check whether the maintenance box or waste-ink absorber is full.
Expected result: A simple cover, ink, or maintenance-box issue clears the warning.
- 03
Power-cycle once
Turn the printer off normally, unplug it for 60 seconds, reconnect it directly to the wall, and check whether the same code returns.
Expected result: A transient warning clears and stays cleared.
Match your symptom, jump to the right fix.
If: The code clears after refilling ink or closing a cover
Then: A low-risk cause was the trigger. Continue normal use.
If: The same code returns after one power-cycle
Then: Match the exact code to the official guide for this model.
If: The guide marks the code as service-required
Then: Stop resetting and contact support with the recorded code.
Usually one of these.
- Canon PRINT discovery, GI-21 ink flow, and rear-tray paper alignment is the model-specific checkpoint to verify first.
- An ink tank is empty, a cover is open, or the maintenance box is full.
- The device is waiting for a network, setup, or maintenance step.
- The code is being read from a different model family guide.
Move to the deeper fix.
Match the code to the official guide
Use the official support page for this exact model rather than a similar-looking printer. Follow the manufacturer sequence before trying a reset.
Expected result: The code maps to a specific, verified fix.
Stop when the code indicates service
If the official guide identifies a hardware or service condition, do not keep forcing resets. Record the code for support or repair. Use the official Canon support page for the exact Canon PIXMA G3260 package before changing firmware or resetting the device.
Expected result: You avoid worsening a hardware fault with repeated resets.
- Do not use a guide for a similar printer model; light patterns and codes are model-specific.
- Repeated resets on a waste-ink or service code can make a repairable fault worse.
Before you reset everything.
Why is the same alarm light still blinking after a restart?
The restart clears temporary state but does not fix a blocked sensor, empty ink tank, or a full maintenance box. On this model, start with Canon PRINT and the official support instructions.
What does a full maintenance box warning mean?
The waste-ink absorber is full. Some tank models let you replace a maintenance box; others require service.
Can I use a guide for a similar printer model?
No. Light patterns and codes are model-specific. Use the exact model support page whenever the pattern is not obvious.
Canon PIXMA G3260 facts that change the fix.
Supplies and parts
- Ink bottles
- GI-21 Black (PGBK), GI-21 Cyan, GI-21 Magenta, GI-21 Yellow
- Maintenance box
- MC-G02 maintenance cartridge (user-replaceable)
- User replaceable
- ink bottles, maintenance cartridge
The ink lamp lights or support code 1640 appears when ink reaches the lower limit. Refill to the fill line.
Error codes and lights
Out of paper.
Load paper and press OK.
Cover is open.
Close the cover.
Paper jam.
Clear the jam.
Ink reached the lower limit.
Refill the ink tanks.
Maintenance cartridge is not installed.
Install an MC-G02.
Maintenance cartridge cannot be used.
Replace with the correct MC-G02.
Maintenance cartridge is not recognized.
Reseat or replace the MC-G02.
Maintenance cartridge is full.
Replace the MC-G02.
Carriage error.
Clear any obstruction and restart.
Print head temperature error.
Let it cool and restart.
Connectivity and operating systems
- Connection
- Wi-Fi · USB
- Wi-Fi
- 2.4 GHz only
- Control panel
- 2-line monochrome LCD
- Paper trays
- Rear tray only (100 sheets)
- Works with
- Windows 10, Windows 8.1, Windows 7 SP1, macOS, iOS, Android
Use the exact model guide.
These links point to the manufacturer resources for this model. Use the manual for panel symbols and the driver page for software or operating-system issues.
Sources checked 2026-08-13.